Home Forums Articles How To's FAQ Register
Go Back   Xoutpost.com > BMW SAV Forums > X5 (E70) Forum
Arnott
User Name
Password
Member List Premier Membership Search Today's Posts Mark Forums Read

Xoutpost server transfer and maintenance is occurring....
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management


Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 07-11-2016, 01:50 AM
Member
 
Join Date: Mar 2012
Location: Boise, ID
Posts: 60
X5Boise is on a distinguished road
BMW E70 X5 Glovebox and Lower Trim Removal DIY

BMW E70 X5 Glovebox and Lower Trim Removal

I just completed taking out my glovebox and replacing the wood trim (my original bamboo was cracking so I got a new one for $186 shipped). Nonetheless, as the instructions are pretty scattered or incomplete, I thought I'd make up a complete guide comprised of PDFs, pictures and links for a DIY. This done on a 2011 LCI X5 35d but should be applicable to all E70 X5 models.

See my PDF version ("BMW E70 X5 Glovebox and Lower Trim Removal DIY") as it has embedded photos to help with removal. Also see the factory PDFs referenced at each step for removal. Combine both for complete information.

Difficulty: 5/10 (mostly trying get out the lower inner bin and larger inner glovebox apart and the glovebox USB port loose)
Time: 1.5 hrs (for a careful first timer)

Tools needed:


Steps

A. Remove Right Air Vent (see PDF)
1. Remove metal trim from right air vent. Start from the upper edge and gently wedge out trim. See PDF.
2. Remove exposed metal screw from right air vent.
3. Remove right side air vent by gently pulling the air vent outwards and towards the back of the car. Put air vent side.

B. Remove Central Air Vent
(see link)
1. Before removing the central air vent, push the open button so the glove box is opened (you'll need it open for access).
2. Remove central air vent by grabbing the metal edge under the metal trim and gently pulling it outwards and back toward the rear of the car. It comes out quite easily. Put an old tshirt or rag under the central vent so it doesn’t scratch your HVAC controls beneath it.
3. There will be 4 electrical harnesess (3 in the center) and 1 on the side. You'll need to put in your small, thin flat head screwdriver in between the wired harness and the end connector, and it will loosen the internal tab and the end connector will come out.
4. Put the central air vent aside.

Link: Removing front centre air vent

C. Remove Navigation Display ("central information display) (see PDF)
1. Using a #2 Philips, unscrew the 2 screws from the lower attachment legs (one on the left side, one on the right)
2. Put a rag beneath the display to protect it.
3. Gently pull the display outward and flip it to expose the back to see the 2 harnesses you'll need to remove one using the thin, flat screwdriver and the other is a round connector with a press in tab, but you'll need to use a thing, flat screwider to help nudge it out. Put the navigation display aside.

D. Glovebox Removal (total pain) (see PDF)
1. On the very left side of the glovebox, there is a rectangular felt cover (about ½”x1”--use a thin screwdriver and wedge it out from the lowermost edge. Remove the hidden T20 screw underneath that cover.
2. On the upper most edge of the glove box, remove two semi-hidden T20 screws. On the very upper right, remove the one T20 screw.
3. If your car doesn't have a changer (like mine), it will be covered with a large back plastic cover. Remove it by lifting the lower edge outward and it will easily come off and it will reveal a silver T25 screw underneath--remove that screw.
4. If your car has a USB plug (see picture for reference), you'll need to remove it. Use the smallest, thinnest screwdriver that you have to wedge it toward the central part of the glovebox (outward), while trying to push down on the silver retaining pin. Yes, it is a pain. And it is quite durable so you can be semi-aggressive in this step.
5. Remove the lower bin (see photo in PDF or JPG--image borrowed from an eBay seller). The glove box itself has a large container composed of 2 parts: a larger surround, and a lower bin. The lower bin is held in by friction tabs along the lip. To remove the lower bin, it needs to be pulled vertically from the larger surround. I found that it was best if I used a 90 degree wedge to pop the left side of the lip of the lower bin upwards (towards the roof of the car), then worked on the right side lip of the lower bin (same action). This is a real pain as well, but once you get this done and removed, it's pretty smooth sailing from here.
6. Remove the larger inner surround. Just pull it up and out (now that you have the small bin removed)
7. You can now remove the four hidden T20 screws (use your T20 bit, 1/4" socket, and 1/4" socket driver)--you can feel them just in the inside edge of the glovebox.
8. Carefully pull out the whole glovebox assembly. You'll need to disconnect a) the upper light module (use thin, small flat screwdriver) and b) the glovebox motor harness (again, use small, thin flat screwdriver)

E. Lower Glovebox Trim Removal (see PDF)
1. Remove tab washer. Use a thin screwdriver to slowly wedge the metal tab washer from the plastic pin. This will release the spring-loaded assist arm.
2. Using pin punch (1/8") and rubber mallet, gently drive the door holding shaft as directed in the PDF. You only need to tap it about 1/2" and you can pull it out. The lower door can now be separated from the main glovebox assembly.

If you ordered a new lower trim door like I did, you'll need to move 2 items from the old lower door: 1) upper trim--just held by 2 screws; unscrew them, and the upper trim comes off--transfer this over; 2) Lower door sleeve bushings--just push in the end snap, and push the bushing out; note the arrows to help orientate the bushings when you push them in your new door.

To reassemble, reverse the steps.

A few reassembly notes:
1. Under E2, you'll need to reverse tap the holding shaft so it stays snug and holds the door in place.
2. Under E1, you can reuse the tab washer, just flatten it so it snaps into the plastic pin.
3. Before you begin to install the new glovebox wood trim, put some Saran plastic wrap on the wood surface (a few layers actually) to to protect during the installation handling.
4. When putting back the central air vent, the wires may get in the way of the 2 vents in the back, so reposition the wires as necessary so the central vent will easily push back into place.

A great resource for repair info on the E70 (where I got my PDFs):

BMW Workshop Manuals
Attached Images
      
Attached Images
File Type: pdf 1 right fresh air vent.pdf (446.5 KB, 1159 views)
File Type: pdf 2 nav central information display.pdf (610.6 KB, 1052 views)
File Type: pdf 3 glovebox 1.pdf (524.4 KB, 1106 views)
File Type: pdf 3 glovebox 2.pdf (463.6 KB, 912 views)
File Type: pdf 4 glovebox lower trim.pdf (646.6 KB, 1083 views)
File Type: pdf BMW E70 X5 Glovebox and Lower Trim Removal DIY.pdf (625.8 KB, 1369 views)

Last edited by X5Boise; 07-12-2016 at 09:10 AM. Reason: updated photos for clarification; updated DIY PDF
Reply With Quote

Sponsored Links

  #2  
Old 07-12-2016, 07:07 AM
Member
 
Join Date: Apr 2006
Location: PA
Posts: 509
Scott ZHP is on a distinguished road
Thanks; I have a new bamboo lower trim sitting on my bench. This will come in handy when I find the time to install it.
__________________
12 E70 3.5i xDrive
03 E46 330i ZHP
01 E53 3.0i
98 E36 323is
12 Audi A4 Quattro
79 Triumph Spitfire
73 MGB
Reply With Quote
  #3  
Old 11-30-2020, 12:03 PM
Member
 
Join Date: Nov 2020
Location: Surrey, England
Posts: 1
sir_dave is on a distinguished road
I know its a few years down the line ... but i partly followed this excellent guide this afternoon. What i would say is that you dont need to do 99% of what is written ...

Simply remove the centre airvent, then move the bar shown below from left to right using a centre punch and the glovebox lid will come off.

There is another arm held on by a small tab, but that will be obvious once the lid is partially removed:



Time to change the glovebox lid was approx 10 mins using this method
Reply With Quote
  #4  
Old 12-19-2021, 09:43 AM
Member
 
Join Date: Nov 2021
Location: España
Posts: 15
blackshark is on a distinguished road
Quote:
Originally Posted by sir_dave View Post
Sé que están unos años después... pero en parte seguí esta excelente guía esta tarde. Lo que yo diría es que no necesitas hacer el 99% de lo que está escrito... Simplemente retire la ventilación central, luego mueva la barra que se muestra a continuación de izquierda a derecha usando un punzón central y la tapa de la guantera se desprenderá. Hay otro brazo sostenido por una pequeña lengüeta, pero eso será obvio una vez que se retire parcialmente la tapa:


El tiempo para cambiar la tapa de la guantera fue de aproximadamente 10 minutos usando este método :pulgar:
hola según el manual de BMW manuals 5116372 pdf Removing And Installing_replacing Lower Glovebox Lid antes de lo que comentas, tienes que hacer lo siguiente: Cierre la tapa de la guantera. Suelte la lavadora de pestañas (1) y retire el pasador (2).

don't need to do it then?
Reply With Quote
Reply

Bookmarks

Tags
glovebox, wood trim; diy

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On





All times are GMT -4. The time now is 08:13 AM.
vBulletin, Copyright 2024, Jelsoft Enterprises Ltd. Search Engine Friendly URLs by vBSEO 3.6.0
© 2017 Xoutpost.com. All rights reserved. Xoutpost.com is a private enthusiast site not associated with BMW AG.
The BMW name, marks, M stripe logo, and Roundel logo as well as X3, X5 and X6 designations used in the pages of this Web Site are the property of BMW AG.
This web site is not sponsored or affiliated in any way with BMW AG or any of its subsidiaries.